Type KR6000
Type KR6000 Top seller
Combining cantilevers of different models, such as between KR3000 and KR6000, is technically not feasible. However, a mixture of different arm lengths, for example 50 cm and 100 cm, is certainly feasible. The important thing here is that the cantilever arms do not protrude beyond the cantilever feet. A combination of 50 cm and 100 cm cantilever arms would require a shelf upright with a depth of 100 cm.
Depending on the type of cantilever racking, our cantilever bays are available in painted and hot-dip galvanized versions (both versions for the KR2500 / KR3000).
The individual cross and diagonal braces are mounted to the bracket of the shelf uprights with the corresponding hexagon bolts, hexagon nuts and washers.
Depending on the height of your shelves, the number of struts (cross and diagonal struts) varies.
You will find the appropriate number of braces in the article description and in the assembly instructions.
The axial dimension is the internal dimension between two shelf uprights. Depending on the cantilever type, we offer these fields in 120 cm (KR2500) and in 100 cm / 150 cm (KR3000 / KR6000).
A rubber strip on cantilever racks is primarily used to protect your stored goods and the cantilevers from potential damage. No additional assembly is required to attach them. The rubber strips are simply glued directly to the desired cantilever arm. For our models KR3000 and KR6000 we offer special matching rubber strips.
Available bay sizes vary depending on the specific cantilever rack model:
- KR2500: Provides bays 120 cm wide, bracing included.
- KR3000: Offers bays in 100 cm and 150 cm sizes, both including bracing. These are also available in a hot-dip galvanized version.
- KR6000: This model also offers 100 cm and 150 cm bays with bracing.
The scope of delivery includes the appropriate number of screws for cantilever racking assembly. The following screws are used for a cantilever racking system:
Bolt anchor, hexagonal bolts / nuts, washer, compensation wedge etc.
With certain models of our cantilever racks you can flexibly adjust the height of the cantilever arms. The KR3000 and KR6000 models offer the possibility to adjust the cantilever arms individually in 5 cm steps. In contrast, the arms of the KR2500 system are permanently welded and do not allow any height adjustment.
Cantilever racking is ideal for the storage of long goods, e.g. wooden beams, steel profiles, pipes and much more. You can additionally equip the cantilever racking with wooden or grating floors, so that the storage of other stored goods is also possible.
Cantilever racking is always fixed by anchoring it to the ground.
Of course, we also offer shelves in customized dimensions.
Please send us your request by e-mail, fax or contact us by phone.
Cantilever rack type KR6000
- Rack height 2m - 6m
- single + double sided cantilever racking with freely adjustable arms in a grid of 5cm in height
- connection of cantilever uprights is made by cross and diagonal braces
- upright profile is screwed to the base
- BGR234-tested
- Easy to assemble
- Best price
- All parts included
BGR234-testedAssembly instructions
Finishes
Painted for indoor use
Single + double-sided versions
Click here for prices and product overview
Hot-dip galvanized for outdoor use
Hot-dip galvanized racks for outdoor use
Overview uprights cantilever rack KR6000
One-sided upright
Stability due to T-beam
Double sided upright
2 different depths - 75cm arm depth (120cm foot depth) and 150cm arm depth (195cm foot depth)
Complete rack stand consists of a double C-profile and the foot part in the form of a T-beam (foot). The upright profile is screwed on the foot.
Stand
Versions + mass
Stand load
One-sided max. 3000KG
Double sided max. 6000KG
Load capacities are valid with evenly distributed load
Mounting stand
Load on foot section
The area of the foot parts of the cantilever rack can be loaded infinitely.
Technical information
Fastening in the floor
Required parts:
Mounted shelf, bolt anchors
- Drill holes: 12mm ∅, 100mm deep
- Blow out holes
- No floor bracket needed. Holes are already integrated / pre-drilled in the base section.
- Drive in bolt anchor with base holder - nut should be flush with thread
- Tighten anchor firmly
- After tightening, the marking in the thread must not be visible!
Please note:
The bolt anchors must be fastened professionally.
Our in-house assembly team will gladly take over the professional assembly of your shelves.
Axle dimension
- The axle dimension describes the width of a shelf bay, as well as the distance between two uprights.
- We offer two different axle dimensions in the widths 100cm & 150cm.
- The different axle dimensions can be freely combined with each other.
- Configure your cantilever rack individually with your desired bay lengths. Our racks can also be extended at any time due to the modular construction.
Assembly struts
Technical information
Assembly of cross and diagonal braces
Required individual parts:
Diagonal strut, cross strut, hexagon bolt, hexagon nut, washer
- The cross and diagonal braces are assembled using angle plate and M10*25 hexagon bolts + washers + nuts. The angle plate is attached directly to the upright profile using M10*80 hexagon bolts + washers + nuts.
- With a 17mm open-end wrench and a ratchet with 17mm nut, the assembly is done in a few minutes.
Diagonal braces + cross braces are used to stiffen between the uprights.
Cantilever arms
Max. Load per arm = 1000kg
Arm is suitable for single and double sided execution.
Arm load
- Total load per cantilever arm
Maximum 1000kg with evenly distributed load
Assembly cantilever arms
Technical information
Assembly of the cantilever arms
1. bring cantilever arm to desired height
2. hook in locking pin
3. attach safety pin
4. attach roll-off protection
Cantilever arm accessories
Magnetic tapes
For labeling storage and berths (wipeable & reusable)
Cantilever rack Rubber strip
Protects from scratching and slipping
Application examples
Optimal for long goods and heavy loads
Accessories - suitable for KR6000
collision protection in L-shape
different heights available > to the collision protection in L-shape
